Description: Rockford Fosgate P3D2-12 Punch P3 12" subwoofer with dual 2-ohm voice coils (PAIR) and Rockford Fosgate T1000-1bdCP Power Series mono sub amplifier — 1,000 watts RMS x 1 at 2 ohms and a SOTS Lanyard PRODUCT DESCRIPTION Rockford Fosgate P3D2-12 Punch P3 Pair of 12" subwoofer with dual 2-ohm voice coils and Rockford Fosgate T1000-1bdCP Power Series mono sub amplifier — 1,000 watts RMS x 1 at 2 ohms Pair of Rockford Fosgate P3D2-12 Two Punch P3 12" subwoofer with dual 2-ohm voice coils 12" subwoofer with dual 2-ohm voice coils anodized aluminum cone with Santoprene surround hybrid StampCast basket provides strength while minimizing weight and resonance Vertical Attach Surround Technique (VAST™) increases cone area power range: 300-600 watts RMS (1200 watts peak power) frequency response: 27-250 Hz sensitivity: 85 dB top-mount depth: 6-11/16" sealed box volume: .75-1.25 cubic feet ported box volume: 1.79 cubic feet Size 12 -inch Impedance 1 ohm or 4 ohms Cone Material Anodized Aluminum Surround Material Santoprene Ideal Sealed Box Volume (cubic feet) 1.02 Ideal Ported Box Volume (cubic feet) 1.79 Port diameter (inches) 4 Port length (inches) 10 Free-Air No Dual Voice Coil Yes Sensitivity 85 dB at 1 watt Frequency Response 27 - 250 Hz RMS Power Range (Watts) 300-600 Peak Power Handling (Watts) 1200 Top Mount Depth (inches) 6 11/16 Bottom Mount Depth (inches) N/A Cutout Diameter or Length (inches) 11 1/16 Vas (liters) 57.7 Fs (Hz) 26.5 Qts 0.49 Xmax (millimeters) 13.3 Features Overview: The Rockford Fosgate Punch P3D2-12 is a 12-inch subwoofer with dual 2Ω voice coils. The sub features a hybrid StampCast basket, quick-release compression terminals, anodized aluminum cone, and Santoprene surround. An anodized aluminum voice coil former and spider venting help keep the subwoofer cool. Dual 2Ω Voice Coils: The dual 2Ω voice coils offer wiring flexibility; when wired in parallel the woofer presents a 1Ω load, when wired in series the woofer presents a 4Ω load. Compression Terminals: The P3D2-12 features spring post terminals which accommodate speaker wire up to 10 gauge. CEA-2031 Compliant: Power handling on the P3D2-12 subwoofer conforms to CEA-2031 industry standards. This means the subwoofer has the capacity to handle power under continuous demand, not instantaneous power handling, that over time, can damage voice coils. FlexFit Basket: The Flex Fit frame utilizes slots (where possible) instead of single screw sized holes; allowing slight adjustment of the speaker when mounted. Trim Ring: To improve the cosmetic look, a decorative trim ring is included that mounts over the flange of the woofer. When using the cast aluminum trim ring the woofer is first mounted with four screws, then the ring is placed on top of the woofer, aligning the final four holes of the woofer with ring. The other four screws are used for these holes to mount the ring and woofer to the enclosure. Without the trim ring the mounting height of the woofer is just under 7/8 of an inch, with the trim ring it's approximately 1-1/16 inches. The diameter of the trim ring is 13-5/16 inches. Enclosure Compatibility Sealed Box: Rockford recommends a sealed enclosure with an optimum internal volume of 1.02 cubic feet (from 0.75 to 1.25 cubic feet is acceptable). Sealed enclosures provide the most control over a woofer, will handle a lot of power, and provide accurate sonic reproduction, making them suitable to all types of music. Ported Box: Rockford recommends a ported enclosure with an internal volume of 1.79 cubic feet using one 4" diameter x 10" long port; this yields a tuning frequency of 40 Hz. Ported (or vented) enclosures typically provide better overall efficiency than sealed so they are suitable for use with smaller amplifiers, giving you more bass output from less power. However, this efficiency comes at the expense of very low frequency output (below 33 Hz). Rockford Fosgate T1000-1bdCP Power Series mono sub amplifier — 1,000 watts RMS x 1 at 2 ohms mono subwoofer amplifier 700 watts RMS x 1 at 4 ohms (1,000 watts RMS x 1 at 2 ohms) 1,000 watts RMS x 1 at 1 ohm CEA-2006 compliant Dynamic Thermal Management cooling system variable low-pass filter (35-250 Hz, 24 dB/octave) selectable subsonic filter (28Hz, 24 dB/octave) variable bass boost (0-18 dB at 45 Hz) optional wired remote bass boost Class-BD amplifier design MOSFET power and output stages preamp-level inputs preamp outputs 4-gauge power and ground leads and an 150-amp fuse recommended — wiring and hardware not included with amplifier no onboard fuses — when installing multiple amps in a system, an additional 150-amp in-line fuse between the distribution block and the amplifier is recommended 13-11/16"W x 2-1/4"H x 8-15/16"D Performance RMS Power Output (Watts x Channels) 700 x 1 Peak Power Output (Watts x Channels) 1320 x 1 Power at 2 Ohms (Watts x Channels) 1000 x 1 Bridged Power (Watts x Channels) N/A Minimum Impedance Bridged N/A Minimum Impedance Unbridged 1 Best Frequency Response 20-250 Hz THD at Rated RMS Power 1% Signal to Noise Ratio 80 dB Input Voltage 14.4v Features Amplifier Class BD Low-Pass Crossover Frequency 35-250 Hz Low-Pass Slope (dB/octave) 24 dB/oct High-Pass Crossover Frequency N/A High-Pass Slope (dB/octave) N/A Bass Boost 0-18 dB Bass Boost Frequency 45 Hz Fan Cooled No Fuse Rating 150 Speaker Level Inputs No Preamp Outputs 1 pair Width (inches) 13-11/16 Height (inches) 2-1/4 Depth (inches) 8-15/16 Features Overview: With its super efficient Class-BD circuit topology and Constant Power configuration, the Rockford Fosgate Power T1000-1bdCP assures maximum power output. Due to its dedicated low frequency response, this amplifier is optimized for mid-bass speakers or subwoofers only. The amplifier is 1-ohm stable (1,000 watts x 1) and will drive a pair of 4-ohm DVC subwoofers or quad-configuration of 2-ohm DVC subwoofers with ease. Class bd Design: Rockford Fosgate bd topology is a revolutionary patented design, integrating a technology that is more efficient than typical class AB and has lower distortion than class D designs. Power bd amplifiers are 75-80% efficient vs. 20-60% efficient class ab amplifiers. This means, more power from your amplifier with less drain on your vehicles electrical and charging system. Constant Power: Its proprietary "Constant Power" configuration provides the ability to instantaneously deliver maximum output power to speakers without regard to its varying impedance while maintaining high-efficiency and thermal performance. Music and speakers have a dynamic relationship. So your listening experience is cleaner, louder and more impressive than ever before. Cast Aluminum Heatsink: The cast aluminum heatsink dissipates heat generated by the amplifier's circuitry. The inherent advantage of casting provides a 30% improvement of cooling over conventional extrusion heatsink designs. Dynamic Thermal Management (DTM): DTM Evenly distributes excess heat across entire amplifier heatsink. DSM (Discrete Surface Mount): DSM utilize 1% tight-tolerances improving efficiency of the circuit, decreases cross-talk from other discrete components and lowers operating temperature. An industry-leading manufacturing process, DSM utilizes high-speed robotics, high-quality 1% tight-tolerance parts and large board traces. The discrete components are laser etched to meet a particular value and a very low tolerance. This lower tolerance improves the efficiency of the circuit, decreases cross-talk from other discrete components and lowers operating temperature. TO-247 MOSFETs: The Rockford Fosgate amplifier use custom TO-247 MOSFETs. These have 60% more metal tab area for more power capacity, lower impedance and improved heat dissipation over traditional TO-220 MOSFETs found in many other amplifier. The MOSFET transistor is the best type of device to use when building a high quality mobile amplifier. The TO-247 has 60% more metal tab area and its unique, fully encapsulated design is capable of housing a silicon die (the heart of the MOSFET) twice as large as the TO-220. The larger die provides more power handling capacity. Additionally, the extra metal tab area ensures that no matter what size silicon die is inside, the thermal impedance will always be lower than in the TO-220 due to improved heat dissipation. MEHSA3: MEHSA3 reduces MOSFET temperatures, lowers distortion, increases durability and prolongs the output device life span. MEHSA3 (Maximum Efficiency Heat Sink Application - gen. 3) is a proprietary process that yields up to five times better heat transfer than traditional FET mounting techniques, using the exact same components. A multi-layer insulated metal substrate operating with minimal thermal resistance spreads heat both downward and outward to quickly dissipate heat from each device across the heatsink. This process combined with Rockford's optimized heatsink designs, DSM (Discrete Surface Mount) technology and MOSFET devices, allows the amplifier to squeeze more watts per cubic inch from every output device as well as provide consistent thermal stability. The 3rd generation creates a dielectric layer between the ceramic topside and the aluminum base that retains all of the electrical isolation and capacitive coupling of the original MEHSA material increasing it's thermal conductivity. The higher power handling results in a 20% reduction in thermal impedance. NOMAD (NOn-Multiplying Advanced Decision): NOMAD is an intelligent protection circuit that uses an analog computer to make real time decisions regarding temperature, voltage, current and impedance. The unit is protected without limiting sound output unless needed. Power and Protection LEDs: The LEDs are located on top of the amplifier. A blue Power LED illuminates when the amplifier is turned on. A red Thermal LED illuminates if the amplifier overheats. The yellow Protect LED illuminates if a short circuit or too low an impedance is detected at the speaker connections. When any of the protection circuits engage, the amp automatically shuts down until the problem is corrected. Controls Internal Crossover: The amplifier features a built-in 24dB/octave Butterworth low-pass filter with a variable crossover point from 35Hz to 250Hz. Punch EQ2: The Punch EQ on-board equalization circuit helps correct for acoustical deficiencies in the listening environment. This control is a narrow band adjustment variable from 0dB to +18dB at 45Hz with a Gyrator based Punch EQ that eliminates frequency shift with boost. Infrasonic Filter: This 28Hz high-pass filter (12dB/octave Butterworth) is designed to prevent frequencies below the audio range from being applied to the subwoofer from the amplifier. This infrasonic filter improves your subwoofer performance and power handling, particularly in vented enclosures. Connections Power Connections: The power and ground terminals are nickel-plated captive c-clamp wire connectors and will accommodate up to 4-gauge wire. An external 150-amp fuse (not included) must be installed on the power wire. If a wiring kit is used which includes a fuse with a value other than 150-amps, the original should be replaced with a 150-amp fuse. The remote turn-on terminal will accept wire sizes of 12- to 24-gauge. A Phillips-head or slotted screwdriver (not supplied) is required to tighten/loosen the terminals. Dual Speaker Terminals: The Power mono-amplifier features two pair of speaker output terminals so you can easily connect two 4-ohm speakers to the amplifier in a 2-ohm load configuration. The two pair of nickel-plated clamp wire connectors will accept 8-gauge to 18-gauge wire. A Phillips-head or slotted screwdriver (not supplied) is required to tighten/loosen the terminals. Differential Input RCA Inputs: The amplifier features a pair of differential RCA input jacks for easy connection of signal level input. Differential input circuitry measures the voltage of both the positive (+) and negative (-) portions of the input signal, subtracting the voltage common to both conductors (noise); resulting in a cleaner signal. Reducing the noise on the input then improves the sound quality of the output. The RCA input jacks are nickel-plated to resist signal degradation caused by corrosion. RCA Outputs: The amplifier also features a pair of RCA "Pass-Thru" jacks which provide a convenient source for daisy-chaining an additional amplifier without running an extra set of RCA cables from the front of the vehicle to the rear amplifier location. The RCA output jacks are nickel-plated to resist signal degradation caused by corrosion. Sound of Tri-State's General Shipping Policies We will ship to anywhere in the continental United States for Free on products indicating free shipping. If you have an APO address, or HI, AK or PR we will need to quote shipping prior to your purchase. Please email via the eBay messaging system and we will be happy to quote your shipping fees. On items that are not indicated as free the shipping rate will be calculated by weight and postal code and can be found using the shipping tab located at the top of the listing. Smaller items less than 1 pound will most likely be shipped via usps first class mail provided they are within measurements. Anything 2-5 pounds will most likely ship via usps priority mail or parcel select provided they are within measurements. Anything over 5 pounds with larger measurement will be shipped via UPS. Please indicate on your paypal payment in the notes section if you cannot receive usps at your physical address and indicate your postal address in the notes section of paypal. International Shipments are generally shipped via Ebays Global Shipping program. Details can be found via this link Ebays Global Shipping Program . On items that are ineligible to ship via Ebays Global ship program, we will ship via usps express mail international. Rates will be calculated by weight and postal code and will NOT include brokerage, duties, customs, and/or taxes. Those fees will be due to the courier upon receipt of the product. Please Note: If you are purchasing an item from us and you are having it shipped to another country please be sure that the product is compatible in that Country prior to purchase. Sound of Tri-State has made things simple by only accepting Paypal as the primary payment method. If for some reason you are experiencing difficulties using paypal please use the contact seller form in eBay and let us know so we can help you with your payment arrangements Please Refer to the Returns Link at the top of the page for more in depth information regarding returns. General Return Policy: No returns will be accepted without a return authorization, which will be given on a case by case basis at Sound of Tri-State's discretion. Please email us using the Ask Seller a Question Link to obtain a return authorization number. NOTE: Any return that does not have a return authorization number written on the outside of the package will not be accepted. We only ship to the address we have on file. Sound of Tri-State has the sole discretion as to what is warrantied. Also Sound of Tri-State is not responsible for any shipping charges. It is our intention to keep you, the customer happy. With that in mind, we will do our best to repair or exchange the item sent back to us in good faith. For returns made 14 days from date of purchase, payment will be refunded less shipping and handling and up to a 15% restocking fee, if a refund is wanted. The item has to be complete in order to receive a refund. If an item is found defective within 14 days, the customer does not have to pay the restocking fees to receive the replacement unit or refund. After 14 days from your receipt date, defective items may be repaired or replaced at Sound of Tri-State's discretion ( Except Remanufactured products, which are only repaired.) The customer will need to send payment for return shipping and handling . The return fee is a non-refundable service fee and will not be part of any credit issued. Please feel free to contact us for any and all support that you should need. We have trained technicians on staff and ready to help with you with any questions. Office Hours: 10AM - 5 PM East Coast Time We encourage you to use email for all communication so we have a record on file. Please contact us using Ebay's Messaging service, Leave your name and the item number in question along with a detailed description of the issue you are having with the item. We are open Monday to Friday from 10 a.m. to 5 p.m. EST ( Eastern Standard Time ). Sales, Payments, Service, Technical Questions or RMA questions: Please use the eBay "Ask Seller Question" Link
Price: 1440.96 USD
Location: Claymont, Delaware
End Time: 2024-08-08T14:14:01.000Z
Shipping Cost: N/A USD
Product Images
Item Specifics
Restocking Fee: No
Return shipping will be paid by: Buyer
All returns accepted: Returns Accepted
Item must be returned within: 30 Days
Refund will be given as: Money Back
Custom Bundle: Yes
MPN: P3D2-12_PKG
Modified Item: No
Bundle Description: Rockford Fosgate P3D2-12 Punch P3 Pair of 12" subwoofer with dual 2-ohm voice coils and Rockford Fosgate T1000-1bdCP Power Series mono sub amplifier — 1,000 watts RMS x 1 at 2 ohms
Voice Coil: Dual
Speaker Size: 12"
Model: P3D2-12+T10001BDCP
RMS Power: 600W
Brand: Rockford Fosgate
Type: Non-Enclosed Non-Powered
